Patlite FV-127JP Manuel d'utilisateur

V95100117MP3 File Playback Circuit BoardUser’s Manual[ TYPE FV-127JP ]

- 10 -5-2-1 Power Input Terminal WiringConnect DC24V.Current ConsumptionFor Maximum Load:About 520mAInrush Current 9A• Ensure wiring is properly per

- 11 -5-2-2 FG Terminal Wiring / Noise Reduction PinWhen the FG terminal is connected to earth ground, depending on the environment, the noise genera

- 12 -5-2-3 Speaker Output Terminal WiringConnect the speaker. (Note Polarity)Regarding Compatable Speakers• The optional SPW-5E (5W) speaker is ava

- 13 -5-2-4 AUX Output Terminal WiringConnect the external amplifi er.External Amp ApplicationThe optional PVA-30 (30W) is available (Sold Seperately)

- 14 -5-2-5 BUSY Output Terminal WiringThe “BUSY” output is sent while a message is in playback. Any external devices, such as a signal tower or rot

- 15 -5-2-6 Input Terminal WiringConnect each terminal through the COM terminal when wiring.Use relays, switches or other non-voltage contacts or NPN

- 16 -6. Volume Adjustment6-1. Volume AdjustmentVolume adjustment for the Speaker and AUX output is possible.• Volume adjustment can be lightly done

- 17 -7. Mode Switch SettingsSet each switch for individual settings.※ The settings don’t take effect until after the soound board is rebooted by repl

- 18 -[Pulse Train]The timing chart above indicates a message stopped during playback.• The timing duration between the input on and off can be no le

- 19 -The timing chart above indicates a message stopped during playback.• The timing duration between the input on and off can be no less than 10ms

- 2 -IndexIntroduction 31. Product Summary 32. Safety Precautions 43. Part Names and Function 54. Installation 75. Wiring 85-1. Terminal Wiring a

- 20 -(A) Normal PlaybackThe message is played back in conjunction with the input. With a oneshot input, play back the message only once and repeat i

- 21 -(B) Memory PlaybackA maximum of 23 voice messages can be stored in memory in order of priority. When the playback voice message ends, the next

- 22 -(C) Input Priority PlaybackIf the next voice message input is turned on while the current message is in playback, the next message will be playe

- 23 -(D) Top Priority Channel PlaybackWhile the message is in playback, if a message of a higher number is entered, the current message will stop and

- 24 -(E) Hold PlaybackWhile the input is held on, the voice message playback is possible.When the input is released, the voice message playback stops

- 25 -7-3. SD Card OperationWhen the SD Card is inserted, the settings for the following (A through D) playback modes are indicated below:Please use t

- 26 -(b) Write Mode The voice message in the internal memory can be overwritten. • To write voice messages into the memory, the following items are

- 27 -【Procedure for transferring voice message data】1. Turn the power off.2. Set DIP switch 5 to “ON” and DIP switch 6 to 'OFF' to set th

- 28 -【Voice Message Exporting Procedure】1. Disconnect the power source.2. Set DIP switch 5 in the “OFF” position and set DIP switch 6 in the “ON” p

- 29 -【Exclusive SD Card Mode Setup Procedure】1. Disconnect the power source.2. Set DIP switch 5 and DIP switch 6 in the “ON” position for the Perma

- 3 -IntroductionThank you for purchasing our Patlite Signal Voice MP3 Playback Circuit Board. Prior to installation, please read through this manual

- 30 -8. Playback MethodAfter performing steps [4. Installation] to [7. Mode Switch Settings], connect to the power source. The power indicator (gree

- 31 -9. Error TableWhen the status indicator LED (red) fl ashes, an error has occurred. Refer to the following table for troubleshooting and its solu

- 32 -10. Binary Input TableCH1 CH2 CH3 CH4 CH5 CH6 CH7 CH1 CH2 CH3 CH4 CH5 CH6 CH7 No. 1 ● No. 65 ●●No. 2 ● No. 66 ●●No. 3 ●● No. 67 ●● ●No. 4 ● No.

- 33 -11. Optional Sales Items1. SD Card (MP3 Voice Message Upload)Model SDV-128P-□□□ Maximum Replay Time: ab. 240 min. Bit Rate: 64kbit/sThe empty

- 34 -12. Before Requesting ServiceProblem Where to CheckNo Sound Coming out of Speaker• Make sure the rated voltage for the power supply terminal i

- 35 -13. Specifi cations13-1 Specifi cationsGeneral Specifi cationsModel Name FV-127JPRated Voltage DC 24VVoltage Range DC 19 to 29VWiring Method M3 Ter

- 36 -13-2 Outer DimensionsProduct specifi cations may change without advanced notice.Due to changes, improvements, etc., contents of this manual may c

- 37 -14. Guarantee ProvisionsThe provisions of this guarantee are in contrast to the purchase of this product from PATLITE Co., Ltd. (henceforth, Our

- 38 -

- 4 -2. Safety PrecautionsIn order to prevent any damage to the user and other personnel or to assets, note the following:The warning indications are

- 5 -3. Part Names and Function1. Installation Holes 4-φ3.5Use the installation holes when mounting. (☞ Refer to pg. 9 [4. Installation])2. Power In

- 6 -5. Volume (Speaker, AUX)Volume adjustment for the Speaker and AUX output is possible.(☞ Refer to pg. 20 [6-1 Volume Adjustment])6. Terminal BusWi

- 7 -4. InstallationUse M3 screws and PCB spacers (not included) when installing the PC Board.* Recommended Spacer Size: 10mm(Use metal spacer when gr

- 8 -• * Ensure the insulation space is suffi cient with a maximum length of 3mm for the lead wires coming from the PCB. If an insuffi cient space all

- 9 -5-2. WiringWiring ExampleWhen handling this product, please do so after discharging static electricity from on the body. Discharge the static el